First appearance: Simple Peg Gun

In this ible, I will express how to make believe a simple Peg Gun. It was my goal to expend as few materials and tools equally affirmable, and to use materials pronto available in nearly houses.

Needed Materials ;

A clothespin

Strong adhesive mucilage or epoxy

(optionally )

A marking or spray paint to colourise the final gun.

Tools requisite;

Pen, pencil, or item to mark woods.

Knife, razor, rotary tool, to off woodwind.

(optionally)

a straight edge puppet

small hobby saw

Step 1: Choose a Good Clothespin.

Let's essay to find a clothespin, arsenic seen on the left over, that has plenitude of room to cut a solid groove into, as well as having enough upstanding forest to take some abuse.

The clothes peg on the right is too thin to take the stress of repeated strikes from the spring. (Also a thoughtfulness when choosing your adhesive.)

Step 2: Disassemble the Clothespin.

Fairly straightforward forward, represent careful non to damage or lose either wood piece surgery the bound.

Prepare the spring aside, we will use it afterwards.

Step 3: Begin Grading the Wood Pieces for Cutting.

You want to start by flipping the pieces so the categoric sides are cladding each other. Make a point the notches where the leap out was sitting align evenly, which is more important than if the front and back describe up. Those can be self-addressed at a later point.

And so, mark the material you will remove.

Step 4: Measure Doubly, Cut Once.

On a project this small, I like to mark all of the material I plan to take. It makes information technology easier to see how well things line up. Remove all material the full depth of the original notches. Remember, the further back your notch on the circus tent firearm, the stronger the spring will return to its resting state.

This likewise means it will be that much harder to cock the gun. Plan accordingly.

Don't forget to remove the barrel material, or you'll end heavenward with

a clicker.

Step 5: Remove Marked Areas.

Since I will mostly be shooting toothpicks, I sized the barrel so there was seeable ink on either side of the projectile when looking at information technology from the top. Be foreordained to have enough space so your projectile will fit nicely into your gun's barrel.

On the bottom piece of wood, cut the barrel all the way thrill with the cavity you made for your spring to travel in. This will ensure your gun will walk out the projectile, sending it flying.

Step 6: Smooth Surface Areas for Glue.

Sleek the barrel and then there will be minimal dredge arsenic your projectile is clarification the gun. Focus Sir Thomas More along the areas where you South Korean won't be able to once the gun is assembled. Use a medium grit sandpaper. You put on't want to remove overmuch material, and you need to equal able to smooth the wood. Medium grit is the most versatile for both.

Step 7: Inalterable Check for Trying on, and Paste.

This is it. Afterward you glue this, you shouldn't pauperization to take it apart. So produce one last bank check to be sure complete of your work will produce the gun you lack. If it's not fitting, this is the last chance to latch on the right way.

Once you are sure enough everything is lining up nicely, prepare your adhesive, and skin-deep areas if needed, (I'm using a tacky heal glue), and glue it in concert.

Let information technology completely dry, so when you test fire, the spring doesn't blow divided your gun.

Step 8: Remove Surfeit Glue or Epoxy After Dry-shod.

When your adhesive has dried and cured accordant to its instructions, remove the gas pedal from its clamps operating theater entrap if used. Check the barrel without doubt aught (like glue or debris) went in at that place spell gluing or solidification. Remove any excess adhesive from inside the barrel, as well as outside the body where it looks badness.

Step 9: Shape Your Firing Mechanisms, Stock, and Barrel.

It is almost done. After a mental testing fire, I distinct to mountain pass the top part a trifle more on the dot. The recoil wouldn't stick around in aim while cocking it. The number one picture should show a 90 grade notch cut to take for it best. Since this is the one with a stronger shot, I think I'll even add some rather spring retention to the body later. As it is, it will fervidness.

To load the saltation, place the spring tips where they bequeath enter at the points I reference with the playpen in both pictures. Actually, the picture shows where the spring sits in a pancake-style position.

Dance step 10: Cock, Load, Aim, Fire!

Beautiful lanceolate. The gun fires when the spring is pushed knock down or pulled back somewhat. It recoil, outstanding the butt of your projectile, transferring it's inertia and fire the weapon.

This is the basic firing mechanism. The body and modifications you take are busy you from here.

This was my firstborn ible. Please let me know how I buttocks improve. I North Korean won't be insulted, as I like hearing how I can be better in any way by and large.

Be the First to Share

Recommendations

  • Anything Goes Repugn 2022

    Anything Goes Contest 2022